Calcium Carbonate Grinding machine
Calcium carbonate is a chemical compound with the chemical formula CaCO3. It is a common substance found in rock in all parts of the world, and is the main component of shells of marine organisms, snails, pearls, and eggshells. Calcium carbonate is the active ingredient in agricultural lime, and is usually the principal cause of hard water. It is commonly used medicinally as a calcium supplement or as an antacid, but excessive consumption can be hazardous
As micro ground calcium carbonate powder plays an important role in many industries from agriculture to light and heavy industries, so the calcium carbonate grinding mill plant is necessary and useful.
The Application of Calcium Carbonate Grinding Machine:
HGM series Calcium Carbonate Grinding Machine is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between 325~2500 mesh.
Performance and features Of Calcium Carbonate Grinding Machine:
1.High efficiency
Under the same final size and power, the product capacity of ultrafine mill is twice than jet mill and agitation mill.
2.Longer lifetime of spare parts
The roller and ring are made of special material, which improve the grinding efficiency a lot. For same material and final size, the lifetime of its wearing parts can reach to more than one year, about 2-5 times as long as that of vertical shaft impact crusher and turbo-mill. Especially when handling calcium carbonate and calcite, the lifetime can reach 2-5 years.
3.High safety and reliability:
There are no rolling bearings and bolts in grinding cavity, so problems caused by bolts shedding or wear of bearings and seal components will never happen.
4.High fineness of products
The product fineness can reach D97=<5um.
5.Environment friendly
The application of pulse dust collector and muffler reduce the pollution and noise of the dust, which has reached national environment protection standard.
Production Line Configuration of Calcium Carbonate Grinding Machine:
The whole set HGM series Calcium Carbonate Grinding Machine consists of hammer crusher, bucket elevator, storage hopper, vibrating feeder, main unit, inverter classifier, cyclone collector, pulse deduster system, high pressure positive blower, air compressors and electrical control systems.
Working Principle of Calcium Carbonate Grinding Machine:
The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse materials return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Technical data of Calcium Carbonate Grinding Machine:
|
Model
|
HGM80
|
HGM90
|
HGM100
|
HGM100A
|
HGM125
|
|
Ring Diameter(mm)
|
800
|
900
|
1000
|
1000
|
1250
|
|
Ring Number/PCS
|
3
|
3-4
|
3-4
|
4
|
4
|
|
Roller Number/PCS
|
21
|
24-32
|
27-36
|
27-36
|
40-44
|
|
Main Shaft Speed/r. p. min
|
230-240
|
200-220
|
180-200
|
180-200
|
135-155
|
|
Input Size/mm
|
≦15
|
||||
|
Finished Size/um
|
5-47(325-3000)
|
||||
|
Capacity t/h
|
0.4-4.5
|
0.4-5.5
|
0.4-6.5
|
0.4-7.5
|
0.7-10
|
|
Outlet Size L*W*H/m
|
13.9*4*6.2
|
14.7*4.8*7.2
|
18*4.6*8.6
|
18*4.6*8.6
|
14*9*10
|
Note: This specification is just referencing, any changes are subject to the products.
Should you have any questions, please do not hesitate to contact me.
Phone: 0086-21-20236178
Contact person: Cherry. Zhao
E-mail: info@clirik.com;clirik_grinder@126.com
Website: http://www.grinding-equip.com; http://www.mill-grinding.com; http://www.saico.net.